1、入水: gate
进入位: gate location
水口形式: gate type
大水口: edge gate
细水口: pin-point gate
水口大小: gate size
转水口: switching runner/gate
唧嘴口径: sprue diameter
2、流道: runner
热流道: hot runner,hot manifold
热嘴冷流道: hot sprue/cold runner
唧嘴直流: direct sprue gate
圆形流道: round(full/half runner
流道电脑分析: mold flow analysis
流道平衡: runner balance
热嘴: hot sprue
热流道板: hot manifold
发热管: cartridge heater
探针: thermocouples
插头: connector plug
插座: connector socket
密封/封料: seal
3、运水: water line
喉塞: line lpug
喉管: tube
塑胶管: plastic tube
快速接头: jiffy quick connector plug/socker
4、模具零件: mold components
三板模: 3-plate mold
二板模: 2-plate mold
边钉/导边: leader pin/guide pin
边司/导套: bushing/guide bushing
中托司: shoulder guide bushing
中托边L: guide pin
顶针板: ejector retainner plate
托板: support plate
螺丝: screw
管钉: dowel pin
开模槽: ply bar scot
内模管位: core/cavity inter-lock
顶针: ejector pin
司筒: ejector sleeve
司筒针: ejector pin
推板: stripper plate
缩呵: movable core,return core core puller
扣机(尼龙拉勾): nylon latch lock
斜顶: lifter
模胚(架): mold base
上内模: cavity insert
下内模: core insert
行位(滑块): slide
镶件: insert
压座/斜鸡: wedge
耐磨板/油板: wedge wear plate
压条: plate
撑头: support pillar
唧嘴: sprue bushing
挡板: stop plate
定位圈: locating ring
锁扣: latch
扣鸡: parting lock set
推杆: push bar
栓打螺丝: S.H.S.B
顶板: eracuretun
活动臂: lever arm
分流锥: spure sperader
水口司: bush
垃圾钉: stop pin
隔片: buffle
弹弓柱: spring rod
弹弓: die spring
中托司: ejector guide bush
中托边: ejector guide pin
镶针: pin
销子: dowel pin
波子弹弓: ball catch
喉塞: pipe plug
锁模块: lock plate
斜顶: angle from pin
斜顶杆: angle ejector rod
尼龙拉勾: parting locks
活动臂: lever arm
复位键、提前回杆: early return bar
气阀: valves
斜导边: angle pin
术语: terms
承压平面平衡: parting surface support balance
模排气: parting line venting
回针碰料位: return pin and cavity interference
模总高超出啤机规格: mold base shut hight
顶针碰运水: water line interferes withejector pin
料位出上/下模: part from cavith (core)side
模胚原身出料位: cavity direct cut on A-plate,core direct cut on B-plate.
不准用镶件: Do not use (core/cavity) insert
用铍铜做镶件: use beryllium copper insert
初步(正式)模图设计: preliinary (final) mold design
反呵: reverse core
弹弓压缩量: spring compressed length
稳定性好: good stability,stable
强度不够: insufficient rigidity
均匀冷却: even cooling
扣模: sticking
热膨胀: thero expansion
公差: tolorance
铜公(电极): copper electrode